Washing Machines, Washer Dryers, Tumble Dryers, Dishwashers, Fridges, Freezers, Fridge Freezers, washing machines washer dryers tumble dryers dishwashers fridges freezers fridge freezers
Find a retailer / Download a brochure / Register your product / Installation Guides 5 Year Guarantee


Welcome to UK Sunday 16 August 2012

Washing Machines

PLUMBING INSTALLATION
Location
Modern washing machines spin at high speed. To avoid excessive vibration during spinning, install the
appliance on a properly supported floor. Always leave at least 5cm of space on each side of the appliance to
allow for possible vibration during spinning of unbalanced loads.


Space for servicing and fitting
Allow space on either side of the appliance for access and servicing.
Water Board Regulations
These instructions are intended only as a general guide and local by-laws and water board regulations
regarding the water connections and drainage from the appliance must be observed.
Water Pressure
The appliance will operate within a wide range of water pressures.
Hot Water (if fitted) minimum 5 N/cm2 (0.5 bar) (7 psi)
maximum 10 N/cm2 (1 bar) (15 psi)
Cold Water minimum 5 N/cm2 (0.5 bar) (7 psi)
maximum 100 N/cm2 (10 bar) (150 psi)
The height of the storage tank in the house must be a minimum of 8 feet above the top of the appliance to
meet the minimum pressure requirements.
Water Supply
1 Most domestic hot water systems are suitable.
2 Multi-point gas heaters can be used if sufficient water pressure is available (check with manufacturer).
3 Single point instantaneous gas water heaters MUST NOT BE USED.
4 If you are in any doubt about the suitability of your hot water system, consult the manufacturer of the
heating appliance or the Gas or Electricity Board.
Water Connections
All the connections and adaptors mentioned in this section can be purchased from your local builder,
plumber or from large DIY stores and electrical outlets.
Filling hoses
All our washing machines are supplied with special high pressure filling
hoses complete with a 3/4" BSP (19mm) female coupling.
Important: Under no circumstances should this coupling be removed from
the hoses (Fig 9).
We will not accept any responsibility for failure of the hoses or water
connections if the factory fitted couplings are removed. The hoses are
designed to be long enough to stay connected while the appliance is pulled
forward for cleaning and servicing.
Fitting the hoses
Important: Remove the hoses from their storage in the drum and fit them to the inlet valves situated on the
rear panel of the appliance. Remember to fit the red hose to the red valve and to insert the rubber washers
into the couplings.
Insert the filter washers (Fig 11/12) in the other

You should not need tools to make a satisfactory seal; excessive force may
damage the connections (Fig 10). It should be sufficient to firmly tighten
them by hand.
Permanent Plumbing
Please make provisions to shut off the water supply to the appliance completely. A separate isolation valve
should be fitted. This will:
1 Avoid the possibility of flooding when the machine is not in use.
2 Allow the appliance to be moved for cleaning and servicing. If you do not
have an existing installation for connecting your appliance, consult a
qualified plumber. There are various methods available.
Discharge into a standpipe - drainage
The top of the standpipe should be approximately 610mm (24") from the
ground. The dimensions from the floor to the underneath of the bend in the
drain hose, should be between 570 - 670mm (221/2"-261/2") (Fig 13). The
take off pipe must be capable of taking a flow of 6 gallons (27 litres) per
minute. The minimum diameter of the standpipe must be 3.81cm (11/2") and
there must be an air gap around the appliance drain hose when fitting into
the standpipe.
Recommended way to plumb in a washer dryer from a combined
waste trap
38mm (11/2")
Min
Air gap
Inspection Elbow
570 - 670mm
(221/2" - 261/2")
W A S H I N G M A C H I N E
8
Fig 10
Fig 12
Fig 11

Temporary connections
It is best to avoid temporary connections where possible. When the appliance runs from sink taps, it can
mean that you are unable to use the sink for over an hour while the appliance completes a programme. In
addition, very hot water will be discharged from the drain hose into the sink and this could be a safety hazard,
especially if you have children close by.
If you must make a temporary connection, be sure that you check the condition of your tap and
keep children away from the discharge area.
The closing of the water valve in automatic appliances is instantaneous and will cause back pressure to the
tap. It is therefore essential that your taps are in good condition or they may leak during use. Even though
your taps may be adequate for everyday use, it is advisable to check the spindle sealing gland of the tap
before connecting your appliance for the first time. To do this, connect the appliance fill hoses to the tap using
your chosen adaptor, making sure the hose sealing washer is in place. If water escapes from the top of the
tap, the gland may need tightening or replacing.
Tap adapters
Tap adapters are available to fit the majority of tap designs. Always ensure that the mesh filter is correctly
positioned in the fill hose coupling. These taps are normally fitted with 5/8" BSP threads (17mm). An adapter
to convert the tap thread to the required 3/4" (19mm) is available from you local builder/plumber merchant.
DO NOT CONNECT TO MIXER TAPS!
Note: All flexible hose connections to be secured with 'Jubilee Clips'
Washing Machine
Washing machine
flexible discharge
hose
Anti-syphon unit
WM4 washing
machine trap
with hose
adaptor
Sink waste to
S.V. pipe
Sink
Spare flexible hose length
for W/M withdrawal
365mm
510mm
Unit Height 900mm
Critical dimension not
to exceed 670mm
W A S H I N G M A C H I N E
9
Fig 14

Temporary drainage connection
The end of the drain hose should be placed over the edge of the sink (Fig 15). Ensure that:
1 The hose cannot be easily displaced (a piece of string or wire can be threaded through the hole in the
plastic moulded hose crook and then attached to the tap).Co-op Electricalshop
2 The water level in the sink cannot cover the end of the drain hose.
3 The plug is removed and the water is able to drain.
4 Children are kept away from the sink while the machine is in operation.
W A S H I N G M A C H I N E
10
Fig 15



Unpacking Instructions

Installation


installation Guides

spares

washing machine handbook

UK PO Box 14, Darlaston Road, Wednesbury, West Midlands, WS10 7TJ

This website is for sale, email links@statefactory.com for details, price £xxxx


Your Ad Here >